 | build 3.0.0.201402161939 |
| build 3.0.0.201402161939 |
All members of the Freescale MCFxxxx ColdFire family of processors
contain a number of on-chip UARTs for serial communication. They all
use very similar hardware. There are some variations such as different
fifo sizes, and some processors contain extra functionality such as
autobaud detection, but a single eCos device driver can cope with most
of these differences. The
CYGPKG_DEVS_SERIAL_MCFxxxx package provides this
driver. It will use definitions provided by the variant HAL
CYGPKG_HAL_M68K_MCFxxxx, the processor HAL and the
platform HAL.
The driver provides partial support for hardware flow control and for serial line status. Only CTS/RTS hardware flow control is supported since the UART does not provide DTR/DSR lines. Similarly only line breaks, and certain communication errors are supported for line status since the UART does not provide other lines such as DCD or RI. On some platforms it should be possible to emulate these lines using GPIO pins, but currently there is no support for this.
Once application code accesses a UART through the serial driver, for example by opening a device /dev/ser0, the driver assumes that it has sole access to the hardware. This means that the UART should not be used for any other purpose, for example HAL diagnostics or gdb debug traffic. Instead such traffic has to go via another communication channel such as ethernet.
The MCFxxxx serial driver should be loaded automatically when
selecting a platform containing a suitable processor, and it should
never be necessary to load it explicitly. The driver as a whole is
inactive unless the generic serial support,
CYGPKG_IO_SERIAL_DEVICES, is enabled. Exactly which
UART or UARTs are accessible on a given platform is determined by the
platform because even if the processor contains a UART the platform
may not provide a connector. Support for a given UART, say uart0, is
controlled by a configuration option
CYGPKG_DEVS_SERIAL_MCFxxxx_SERIAL0. The device
driver configuration option in turn depends on a HAL configuration
option CYGHWR_HAL_M68K_MCFxxxx_UART0 to indicate
that the UART is actually present and connected on the target
hardware. If a given UART is of no interest to an application
developer then it is possible to save some memory by disabling this
option.
For every enabled UART there are a further four configuration options:
CYGDAT_DEVS_SERIAL_MCFxxxx_SERIAL0_NAMEEach serial device should have a unique name so that application code can open it. The default device names are /dev/ser0, /dev/ser1, and so on. It is only necessary to change these if the platform contains additional off-chip UARTs with clashing names.
CYGNUM_DEVS_SERIAL_MCFxxxx_SERIAL0_ISR_PRIORITYBy default the driver arranges for the UARTs to interrupt at a low interrupt priority. Usually there will be no need to change this because the driver does not actually do very much processing at ISR level, and anyway UARTs are not especially fast devices so do not require immediate attention. On some Coldfires with MCF5282-compatible interrupt controllers care has to be taken that all interrupt priorities are unique.
CYGNUM_DEVS_SERIAL_MCFxxxx_SERIAL0_BAUDEach UART will be initialized to a given baud rate. The default baud rate is 38400 because in most scenarios this is fast enough yet does not suffer from excess data corruption. Lower baud rates can be used if the application will operate in an electrically noisy environment, or higher baud rates up to 230400 can be used if 38400 does not provide sufficient throughput.
CYGNUM_DEVS_SERIAL_MCFxxxx_SERIAL0_BUFSIZEThe serial driver will maintain software buffers for incoming and outgoing data. The former allows data to continue to arrive even if the application is still busy processing the previous transfer, and thus potentially improves throughput. The latter allows the application to transmit data without immediately blocking until the transfer is complete, often eliminating the need for a separate thread. The size of these buffers can be controlled via this configuration option, or alternatively these buffers can be disabled completely to save memory.
There are additional options in the generic serial I/O package
CYGPKG_IO_SERIAL which will affect this driver. For
example CYGPKG_IO_SERIAL_FLOW_CONTROL and its
sub-options determine what flow control mechanism (if any) should be
used.
This package also defines some configuration options related to testing. Usually these options are of no interest to application developers and can be ignored.
The generic driver needs some information from other packages about the exact hardware, for example how many UARTs are available and where in memory they can be accessed.
Another package, usually the processor HAL, should provide one or more
options CYGHWR_HAL_M68K_MCFxxxx_UART0,
CYGHWR_HAL_M68K_MCFxxxx_UART1 or
CYGHWR_HAL_M68K_MCFxxxx_UART2. These may be
calculated or user-configurable depending on the processor.
The device driver will also look for symbol definitions
CYGHWR_HAL_M68K_MCFxxxx_UART0_RTS and
CYGHWR_HAL_M68K_MCFxxxx_UART0_CTS, and the
equivalents for the other UARTs, to determine whether or not these
handshake lines are connected. These may be configuration options or
they may be statically defined in a HAL I/O header file. The platform
HAL should also implement the generic serial package's interface
CYGINT_IO_SERIAL_FLOW_CONTROL_HW if appropriate.
If RTS is connected then the driver will also look for a symbol
CYGHWR_HAL_M68K_MCFxxxx_UART0_RS485_RTS. This
enables partial support for RS485 communication in that the device
driver will arrange for the RTS line to be asserted during a transmit.
The driver has no support for more advanced RS485 functionality such
as multidrop.
In addition the driver assumes the standard MCFxxxx HAL macros are defined for the UART base addresses and the registers. The driver primarily targets MCF5282-compatible UARTs but there is also some support for functionality available on other members of the Coldfire range, for example the MCF5272's fractional baud rate support.